Author: Larrin
Tests of Knife Edge Toughness
Thanks to Jaethan Reichel for becoming a Knife Steel Nerds Patreon supporter!
In an earlier article I wrote about the microscopic mechanisms by which chipping and micro-chipping occurs in edges. However, that article did not cover specific tests of edge toughness. Correlating conventional toughness tests with edge toughness is difficult for many reasons:
Sharpness vs Cutting Ability
Thanks to Matthew Berry for becoming a Knife Steel Nerds Patreon supporter!
CATRA, Sharpness, and Cutting Ability
I got several good comments on the article about CATRA edge retention testing regarding sharpness and cutting ability. The edges tested with more acute angles (20° edge is more acute than 50°) started out cutting better and remained that way through the standard 60 cuts. However, the measured width of the edge with the worn 20° edges was larger than with the 50°. So this leads to a question: which was sharper? And if the 50° was indeed sharper due to its narrower edge then why was it not cutting as well?
Five Myths About Damascus Steel
Knife Steel Nerds coffee mugs have been shipped to all current “Ultimate Steel Nerd” Patreon supporters.
What is Damascus Steel?
There are two major steel types that are called Damascus:
1. Crucible, or Wootz, steel was first produced in India and Central Asia and produced into swords anciently from at least the 3rd century AD [1]. It is made by producing small ingots of high carbon steel that are then forged and thermal cycled in a specific manner to lead to carbide bands that produce the final pattern when the steel is etched [2][3]:
Book Recommendations for the Knife Steel Nerd
Update 10/29/2020: Since writing this article I published my own book called Knife Engineering: Steel, Heat Treating, and Geometry. Of course I still recommend the other books on the list below.
Thanks to Ben Wendel, William Brigham, Jeff Schafer, and Simon Moeskjær Balle for becoming Knife Steel Nerds Patreon supporters!
Steel History – The First Stainless Steel was for Knives
Update 7/23/2018: I added a small piece of new information on the development of 440C steel to the article.
Thanks to Greg Hanson for becoming a Knife Steel Nerds Patreon supporter!
The writing of this article was made much easier due to the existence of The History of Stainless Steel by Harold Cobb [1]. If you want more information on the history of stainless and the people who developed it, check out the book.
Bainite vs Martensite – The Secret to Ultimate Toughness?
Thanks to Thomas Busch for becoming a Knife Steel Nerds Patreon supporter!
Misc. update: I have added a set of supporting micrographs to the introduction to Austenitizing steel.
Tempered Martensite
To begin describing what bainite is it makes sense to start with martensite first. To form martensite we heat up the steel to high temperature to transform to a phase called austenite where we dissolve carbon in between the iron atoms (see Austenitizing Part 1), then quench the steel to lock in the carbon and form a hard phase called martensite (see What Makes Quenched Steel so Hard?). Following that we temper the martensite to allow some of the carbon out and increase the ductility of the martensite; the carbon comes out as very small carbides, a compound of iron and carbon (see What Happens During Tempering?). In the article on martensite formation I shared the following YouTube video to see the formation of the martensite laths:
Interview with Knifemaker Phil Wilson about Performance Blades and His Journey with Knives
Thanks to Andrew Demko, Andre Bassett, and Landon Horne for becoming Knife Steel Nerds Patreon supporters! My plans for research are expanding with each new supporter and I’m very excited about the possibilities. Please sign up if you are interested in funding knife steel research.
Review – Kevin Cashen’s Guide to 1080 & 1084
Thanks to Edward Braun, Mark Reich, and Alex Kaplan for becoming Knife Steel Nerds Patreon supporters!
Misc. updates: I added some toughness numbers that I had previously been unable to track down comparing 440C and 154CM to the 154CM article. I also added a summary of a very interesting new journal article about the effect of grain size on steel toughness to the Grain Refinement article.
Maximizing Edge Retention – What CATRA Reveals about the Optimum Edge
Thanks to Ed Schempp, Matus Kalisky, and Chin Lim for becoming Knife Steel Nerds Patreon supporters! Your support allows us to fund CATRA studies.
CATRA
Update 1/6/2020: I have since written more articles about CATRA looking at the effect of steel type: Part 1 and Part 2
How Much More Chromium Does D2 Need to be Stainless?
Thanks to Devon Craun for becoming a Knife Steel Nerds Patreon supporter! Your support is funding knife steel research.
Some materials like aluminum form a passive oxide layer that prevents further corrosion. Steel is not one of those materials. Instead, steel forms iron oxide, or rust, that doesn’t protect the underlying iron and flakes off leading to further corrosion. However, when sufficient chromium is added then a chromium oxide passive layer forms which protects the steel from corrosion in a similar way to a metal like aluminum with its own aluminum oxide layer. A simple schematic diagram shows the passive film vs rust [1]: